Differences

This shows you the differences between two versions of the page.

@@ Line 1: / Line 1: @@
+http://reprap.org/wiki/RepRap_Morgan
+=== hardware ===
+Hawthorne True Value
+  * M8 Nut $0.38
+  * M8 Washer $0.18
+  * M8 threaded rod up to 100mm (too short)
+  * brass tubing up to 380mm (too short)
+Winks
+  * M8 threaded rod 1m long $10
+  * copper tubing 5/8"/15.875mm(actual) $7.99 4ft/1219mm
+  * copper tubing 7/8"/22.225(actual) $12.99 4ft/1219mm
+VXB Bearing
+  * 10 Bearing 608ZZ Shielded 8x22x7 Miniature Ball Bearings $7.37 ($5.74 shipping)
+=== printable parts ===
+print all the items from https://github.com/qharley/Morgan
+|| filename || specs || Thanks to ||
+|| 01-pvc_pipe_support_a.stl || || ||
+|| 02-pvc_pipe_support_b.stl || || ||
+|| 03-z_mount_bottom_12mm.stl || || ||
+|| 03-z_mount_bottom_8mm.stl || || ||
+|| 04-z_mount_top_12mm.stl || || ||
+|| 04-z_mount_top_8mm.stl || || ||
+|| 05-motormount_short.stl || || ||
+|| 06-motormount_tall.stl || || ||
+|| 07-drivewheel_rod.stl || || ||
+|| 08-drivewheel_tube.stl || || ||
+|| 09-22mm_6805_bearing_adaptor.stl || || ||
+|| 10-bed_arm_left_12mm.stl || || ||
+|| 10-bed_arm_left_8mm.stl || || ||
+|| 11-bed_arm_right_12mm.stl || || ||
+|| 11-bed_arm_right_8mm.stl || || ||
+|| 12-bed_z_mount_bracket_12mm.stl || || ||
+|| 12-bed_z_mount_bracket_8mm.stl || || ||
+|| 13-bed_rear_mountclips.stl || || ||
+|| 14-bed_front_mountclips.stl || || ||
+|| 15-hall_endstop_holder_12mm.stl || || ||
+|| 15-hall_endstop_holder_8mm.stl || || ||
+|| 16-leadscrew_shaft_motor_mount.stl || || ||
+|| 17-Morgan_arm_PSI_a.stl || ABS || sandwich ||
+|| 18-Morgan_arm_PSI_b.stl || ABS || sandwich ||
+|| 19-Morgan_arm_Theta_a.stl || ABS || sandwich ||
+|| 20-Morgan_arm_Theta_b.stl || ABS || sandwich ||
+|| 21-Morgan_toolhead.stl || || ||
+|| 22-Leadscrew-nut_Alpen8mmSDS.stl || || ||
+|| 23-extruder_bowden_adaptor.stl || || ||
+|| 24-Morgan_Spool_holder.stl || || ||
+|| cap_2.stl || || ||
+|| cloud_fix_stl.bash || || ||
+|| Eckstruder_Big_Gear_Herringbone.stl || || ||
+|| Eckstruder_Block_for_Prusa.stl || || ||
+|| Eckstruder_Idler_Block_for_Prusa.stl || || ||
+|| Eckstruder_Small_Gear_Herringbone.stl || || ||
+|| thumb_knob_M4_extruder.stl || || ||
+|| tighteningCone_2.stl || || ||