User Tools

Site Tools


esp-ftl

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
esp-ftl [2019/04/05 16:52] – [Rev 2019 Mar] donpdonpesp-ftl [2019/11/24 18:08] donpdonp
Line 27: Line 27:
 ## FTL 2016-July ## FTL 2016-July
  
-{{http://donp.org/i/5SjT.jpg?500}}+{{hardware:esp12-ftl.jpg?500}}
  
 ## May 2016 Rev ## May 2016 Rev
Line 111: Line 111:
 ## Pins that matter for NodeMCU ## Pins that matter for NodeMCU
  
-  * Grounds: 1 or [17,18,19,20]+  * Grounds: 1 or center pads[17,18,19,20]
   * Power: 3   * Power: 3
-  * NeedHigh: 4[float ok], 11[float ok], 12[float ok]+  * NeedHigh: 4/CH_PD[float?], 11/IO2[float high], 12/IO0[float high]
   * NeedLow: 9   * NeedLow: 9
  
Line 125: Line 125:
   * add single neopx?   * add single neopx?
  
-## Reflow technique+## Hotplate Reflow technique
   warmup while on 'W' on WARM   warmup while on 'W' on WARM
   place board    place board 
Line 173: Line 173:
     * esp32 (waiting) + winbond 4mb flash w25q32fv     * esp32 (waiting) + winbond 4mb flash w25q32fv
   * USB/Serial   * USB/Serial
-    * USB Serial CP2102N, bonus 100ma 3.3v reg $1.66 (out of stock)+    * USB Serial CP2102N, QFN20. bonus 100ma 3.3v, 24Mhz clock! reg $1.33
     * FT230X, batt chg detection, QFN16 4x4 $2.04     * FT230X, batt chg detection, QFN16 4x4 $2.04
     * XR21V1410, QFN16 3x3 $3.88     * XR21V1410, QFN16 3x3 $3.88
Line 195: Line 195:
  
 ## 8285 Nov 2016 ## 8285 Nov 2016
-  * ESP needs a 26MHz Clock + 2 10pF caps+  * ESP needs a 26MHz Crystal + 2 10pF caps
   * JST connecors were changed to the wrong size   * JST connecors were changed to the wrong size
   * power CAP back-fed into data pin and fried! zener diode BAT-54S?   * power CAP back-fed into data pin and fried! zener diode BAT-54S?
Line 235: Line 235:
   * update: only MOSI & CLK needed.    * update: only MOSI & CLK needed. 
   * update: any two gpio pins work   * update: any two gpio pins work
-  * Add: 5v voltage monitor (v divider on adc) +  * Add: 5v voltage monitor (v divider on adc, no room on adc. channels?
-  * Ambient light measure+  * Ambient light measure (GL5528 10k-20k ohm, pinout 3.3v, ADC 0-1v)
   * Flip gnd/data for temp sensor   * Flip gnd/data for temp sensor
   * add pwr-data resistor for sensor   * add pwr-data resistor for sensor
Line 251: Line 251:
   * attiny85 $2.24   * attiny85 $2.24
   * laserbee 8051 $1.38   * laserbee 8051 $1.38
-  * 1.5-5.5v -> 3.3v reg 500mA $0.88 (lavalamp test: 20ma observed)+  * 1.5-5.5v -> 3.3v reg 500mA $1.09  LD39050PU33R  (lavalamp test: 20ma observed
 +  * 2-8v -> 3.3 reg 400ma $0.87 XC6203E332PR-G (easier to solder
   * 0-15v -> 3.3v reg 800mA $1.10   * 0-15v -> 3.3v reg 800mA $1.10
   * mini-usb connector $0.46   * mini-usb connector $0.46
Line 260: Line 261:
   * bme280 press/humid/temp $3   * bme280 press/humid/temp $3
   * VEML RGB sensor $2.12   * VEML RGB sensor $2.12
 +
 +# ESP12s flash params
 +  SPI Speed      : 40MHz
 +  SPI Mode       : DIO
 +  SPI Flash Size & Map: 32Mbit(512KB+512KB)
 +
 +
 +# 3.3v vreg considerations
 +
 +  * https://www.mouser.com/ProductDetail/Texas-Instruments/LMS8117AMP-33-NOPB?qs=sGAEpiMZZMsGz1a6aV8DcBojudwDyMGacuHNsdAV7yU%3D
 +  * https://www.mouser.com/ProductDetail/STMicroelectronics/LD29150DT33R?qs=sGAEpiMZZMsGz1a6aV8DcPlO7P8YByjW32ksfjzOXyE%3D
 +
 +# serial CTS/RTS 2019Nov
 +  * watched CTS/RTS on esp12s
 +    * CTS always high
 +    * RTS always low
 +    * no help
  
esp-ftl.txt · Last modified: 2024/01/31 04:08 by 127.0.0.1